Design, Simulation and Analysis of Dual Nozzle, Leg Operated Pesticide Sprayer

DOI : 10.17577/IJERTV10IS010080

Download Full-Text PDF Cite this Publication

Text Only Version

Design, Simulation and Analysis of Dual Nozzle, Leg Operated Pesticide Sprayer

Upendra Dani

B-Tech. Mechanical Engineering Vishwakarma Institute of Technology Pune, India

Vishwajeet Desai

B-Tech. Mechanical Engineering Vishwakarma Institute of Technology Pune, India

Ashish Mali

B-Tech. Mechanical Engineering Vishwakarma Institute of Technology Pune, India

Milind Rane

Professor,

Anshul Dahiwalkar

    1. ech. Mechanical Engineering Vishwakarma Institute of Technology Pune, India

      Vishwakarma Institute of Technology Pune, India

      Abstract Agriculture is the livelihood of 58 percent of Indias population. A pesticide pump is a mechanical tool which is used by farmers to spray insecticides, pesticides, weedicides, and other liquid chemicals. Hand operated pesticide pumps consists of a handle and a spraying nozzle. It is a cheaper option than that of its electrical and combustion engine powered counterparts. But its operating efficiency is lesser than the others. The main benefit of the proposed design is that it will be a balance of both cost and efficiency by using twin piston pump arrangement. The additional design goals were to achieve better ergonomics and dual nozzle while spraying. To assess the pressure and performance ANSYS-FLUENT and for simulation solid works and Linkage have been used.

      Keywords Agriculture, Bell crank, ergonomics, leg operated, pesticides , pump, pistons ,weeder pump.

      1. INTRODUCTION

        As India is said to be an agriculture-based country, we can observe that the farmers are using conventional equipment which have little to no development in past few years [1]. One of such equipment is Pesticide sprayer.

        Due to increase in labor cost and decrease in labor availability there is a need to increase efficiency and decrease in time consumption for such equipment. So, to minimize human effort by maximizing working efficiency of conventional pesticide pump by altering pumping actuation mechanism is our goal.

        The pumping function is done by two individual piston pumps which are operated by a self-design bell crank-based actuation mechanism connected to individual legs/thigh.

        This can spray twice as much as fluid as of a conventional single piston hand operated pump. This will help saving time and human efforts.

        To investigate the flow, pressure, and structural durability we used ANSYS Fluent and ANSYS static structural model. (For such we used no slip streamline model for CFD ).

      2. LITERATURE REVIEW

        Started studying with the working mechanism of conventional hand operated pesticide pump. The design of it was also observed thoroughly.

        The alternative pumping was also studied which made our concepts regarding pesticide pump clear.[1]

        1. Pre-requisites & calculations Measurement of pumps per minute.

          • Reading taken by physical testing of conventional pesticide pump for 3 different people.

          • This data is used for calculation of bore and stroke of our pump.

            Reading no.

            Readings (ppm)

            Time (s)

            1

            26

            60

            2

            24

            60

            3

            25

            60

            Average=

            25 ppm

            60 sec

            Table 1-Observations 1

            Measurement of leg movement frequency

          • This test has been done on 3 different people for minimizing error and broader reading range.

          • The value has been divided by 2 because individual leg will have its separate pump and mechanism.

            Reading No.

            Value

            Value/2

            Time (s)

            1

            66

            33

            60

            2

            58

            29

            60

            3

            52

            26

            60

            Average=

            58.66

            29.33

            60

            Table 2 Observations 2

      3. DESIGN OF PISTON PUMP

        For designing piston, the values for conventional (OEM) pesticide pump were considered-

          • OEM pump- 1)Bore =55mm 2)stroke=55 mm

        1. Total volume displaced in 1 cycle=

          v=pi*[(bore/2) ^2] *stroke mm^3

          =130670.6194 mm^3

          Hence, v=130.6 cc

          Therefore, volume displaced in 1 minute by hand pump = 3250 cc = 3.25 litre.

          • For keeping constant flowrate of 3.25 litre per minute the new cylinder displacement per minute should be the same.

          • From the testing readings 29.33 oscillations per minute are done.

          • NEW pump-

        let new cylinder displacement = x x*29.33=3250

        Therefore x=110.8080 cc = new cylinder displacement-[2]

        Figure 1-Piston Internals

        Figure 2-Piston pump CAD

        From the bore diameter and the required mass flow rate of the pump we simulated a pressure and flow simulation

        Analysis.

        Figure 3-Pressure Inside Pump analysis

        The results were verified form an OEM pump spec sheet.

        Figure 4- OEM spec sheet

        Therefore, the force applied on the piston will be =849.4N Structural Analysis of Pump [3]

        Due to changes dimensions and specifications, we carried out structural analysis and found that there was not much of deformation(0.5mm) and a bearable stress was being exerted On the plastic piston.

        Figure 5-Structural Analysis of pump.

      4. ACTUATION MECHANISM

        By using mechanism simulation software linkage, we iterated our first actuation mechanism. Considering the lengths to be ideal and a simple mechanism simulation was done.

        Image-2 linkage simulation of actuation mechanism using bell crank.

        We designed the mechanism inspired from slider crank Mechanism.

        -From figure 1 I is the stationary/fixed point while J will be the moving end connected to the thigh and point B will be moving joint. While E is the piston head and N be TDC and M be BDC of the piston mechanism.

        We had to make the piston travel from TDC to BDC within 40deg of rotation of the crank, so at the crank we designed a

        bell crank, and we optimized the lengths of the links (BI, EB) so that we achieved the crank rotation to be 40deg.

        conventional pump so it will be easier for manufacturers to adapt.[1]

        Then from that we got the stroke to be 100mm, then from [1] calculations of displacement the bore was calculated i.e.,

        =37.4mm.

        -New Bore=37.4mm New Stroke=100mm

        Calculation of forces applied on the bell crank at the extreme conditions during its operation-

        Pressure P =0.4N/mm^2

        Area (of piston) A =2123mm^2

        Force applied on the piston head Fp = 849.4N Angular velocity =0.1745 rad/s

        Length of bell crank arm R=200mm From the above data

        Velocity of piston Vp = *R (Sin + (Sin2 /n)) [3]

        Vp=0.1745*200(1+0)

        Vp=34.9mm/s———-(Piston Velocity) Force applied on the Bell crank Arm (Ft)= Fp*Vp=Ft*Vt [3]

          1. *34.9=Ft*43.625

            Ft=679.584N———–(Force applied by end user)

            From the above forces we did structural analysis.

            Figure 6-Structural Analysis of Bell crank.

            Then we found out that there was room for optimization and weight reduction which will reduce material cost as well.

            Figure 7- Structural Analysis of Optimized Part.

      5. PUMP CONTAINER DESIGN

        Fluid inside the container should last for a time even though the rate of flow has been doubled so we increased the dimensions of the container to hold more fluid than earlier. We tried to keep design of container simple and inspired by

      6. ERGONOMICS

        To be useful for all body types and height we worked on what could be the possible solutions with keeping the cost low to make its fitting around the waist and thigh adjustable, in the end we concluded using metal and Velcro straps, out of which metal will provide rigidity to the links when in working condition and Velcro will provide adjustability to the user.

        Figure 8-Side View of Mechanism On pump.

        Figure 9-Waist Belts for wearing.

        Figure 10- Thigh Belt for Wearing and Support.

      7. MATERIALS

        Materials/Components

            • Container, piston-plastic(polypropylene) Tensile strength-3200-5000psi

              Density-0.91-0.94g/cm^3

            • Rods- mild steel painted hollow rods

            • Bell-crank-laser cut mild steel

            • Velcro

      8. RESULTS AND DISCUSSION

        A completely new type of actuation of sprayer is designed which has capability of doing twice the amount of work at the same time by a single user at cheaper cost than of its electronic and engine counterparts.

        It is reliable and just as effective in spraying as conventional sprayers.

        It also has ergonomic adjustable belts to suit all body types. It is cheaper and easy to maintain and easy for farmers to repair themselves if something goes wrong.

        • Bore Diameter-37.4mm

        • Stroke Length-100mm

        • Maximum pressure inside Piston around 4 bars.

        • Force required at piston head=849.4N

        • Force to be applied by thigh=679.584N

        Flow simulation results from ANSYS-FLUENT model.

        Figure 11-Complete Product Assembly.

      9. CONCLUSION

        Increased mass-flow rate, easy operation and almost twice the operating efficiency is achieved.

        The output of the pumping rate might change with the atmospheric conditions such as temperature, density of air and liquid being sprayed.

        Further we can optimize the sprayer efficiency with mass flow optimization and better piston configuration form user feedback.

        Figure 12- Demonstration.

      10. ACKNOWLEDGMENT

        This work is partially supported by the department of Mechanical engineering, Vishwakarma Institute of Technology, Pune, Maharashtra. We offer our sincere gratitude to Prof. Milind Rane who guided and supported us.

      11. REFERENCES

  1. Mr. Pankaj B. Gavali, Dr. Shashidhar. S. Kalashetty A Review on Pesticides Sprayer Technology Approach in Ergonomics, Economics and Ecologic in Agriculture Field.

  2. S. Kumara, D.Ll. Daviesb,1, J. Watton A complete analysis of axial piston pump leakage and output ow.

  3. Perera, M.S.M., Theodossiades, S. and Rahnejat, H.2007. A multi- physics multi-scale approach in engine design analysis. Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-body Dynamics, 221(3), pp. 335-348

2 thoughts on “Design, Simulation and Analysis of Dual Nozzle, Leg Operated Pesticide Sprayer

Leave a Reply to Shreyas